Anti-tank guided 9M123 and 9M123F missiles
|The maximum firing range||is at least 5000 m.|
|The minimum firing range||400 m.|
|Missile flight speed||supersonic|
|The warhead 9H146-1 for 9M123||tandem cumulative (armor penetration 1000 ... 1100 mm for DZ).|
|The warhead 9H146F for 9M123F||a high-explosive (with SLM, TNT equivalent of at least 13.5 kg).|
|Warhead caliber||155 mm.|
|The length of the missile in the Transport and launch container||2300 mm.|
|The mass of the missile in the Transport and launch container||not more than 62 kg.|
|The altitude range of the combat use of 9M123 and 9M123F missiles above sea level||up to 3,000 m.|
- 9P157 combat vehicle (699-sb2 chassis on the BMP-3 units and assemblies);
- anti-tank guided missile 9M123;
- anti-tank guided missile 9M123F;
- machine test and check 9V945 (for testing combat vehicle);
- machine test 9B990 (for testing missiles);
- test equipment 9В946 (for missile testing);
- Spare parts kit (single, group and repair);
- simulator 9F852;
- practical guided missile 9M123 Pract;
- educational missile 9M123Maket;
- training rocket with operating on-board equipment 9M123 Training;
- training rocket 9M123
- 9M123F split training missile;
- training target 9F734;
- educational and technical posters kit.
Fighting vehicle 9P157
Chassis 699-sb2 on the nodes and units of the BMP-3.
The crew car 9P157 consists of 2 people. The machine has high maneuverability and is capable of operating in the conditions of the damaging factors of weapons of mass destruction. Ammunition of the 9P157 combat vehicle is 15 anti-tank guided 9M123 and 9M123F missiles in an automated combat pack. Loading a retractable launcher from an automated combat pack of combat vehicles with a choice of rocket type is performed automatically. Missiles are loaded into the ammunition using a loading mechanism or manually. On the retractable launcher of the combat vehicle are two containers with missiles.
9P157 combat vehicle is equipped with an optical-laser guidance system and a radar control system.
The rate of fire fighting vehicles up to 4 missiles / minute. Missile launch is performed from the place, sequentially. From one combat vehicle, two missiles can be simultaneously aimed at two targets.
9P157 combat vehicle firing sector:
- in azimuth from minus 85 to plus 85 degrees;
- on a corner of a place from minus 5 to plus 15 degrees.
Anti-tank missiles 9M123 and 9M123F
The rocket is made according to the normal aerodynamic configuration.
In the tail part of the rocket, the instrumental part and the drive of the rudder are located, which are located in front of the nozzle block and are arranged perpendicular to the nozzle axis.
The rocket control system includes a radio receiver located in the hardware of the rocket and a photo-receiver device that provides automatic rocket guidance in the radio beam or semi-automatic rocket guidance in the laser beam. The type of guidance system is given by the voltage on the contacts of the launcher.
Testing machine 9В990
Control and Testing Machine 9B990 is designed to conduct routine inspections of 9M123, (9M123F, 9M123 Pract., 9M123 Training) missiles during operation and storage.
The composition of the Control and Testing Machine 9V990:
- base chassis - car type Ural-4320;
- body-container K5350;
- test equipment 9V981.
Ural-4320 car with a 6x6 wheel formula is equipped with a four-stroke diesel engine with liquid cooling.
KK4.2 container body is intended for checking missiles and other auxiliary units and instruments.
A diesel-electric unit (generator) with a power of 15.8 kW and generating voltage 380V (three-phase with a frequency of 50 Hz) is installed in the container body to supply power to the Shot Blasting Machine equipment and the rockets to be tested;
The generator is installed in the compartment of the body-container. Power supply is made to consumers without removing the generator from the compartment.
Shot Blasting Machine 9V990 is also supplied with power from an industrial three-phase AC network of 380V ± 10% with a frequency of (50 ± 1) Hz.
Standard measuring devices are designed to test the subsystems KPA 9V981.
The verification of missiles is carried out with the help of the KPA 9V981 located in the Shot Blasting Machine 9B990. Verification of missile parameters can be carried out both in automated and in manual mode.
Main technical characteristics of KPM 9B990
The method of controlling the parameters of rockets is automated, parametric, tolerant.
Performance Control and Testing Machine 9V990 at least 15 missiles per hour.
The deployment time of the PMC from the traveling position to the working 2 hours.
Closing time Control and Testing Machine from working position to traveling 15 min.
Duration of continuous work Control and Testing Machine 8 hours.
Сombat crew: 1 driver and 1 operator.
The power consumed by the Control and Testing Machine from a three-phase network 380 V 50 Hz - 8 kW.
The time of the readiness of the Control and Testing Machine to work from the moment the power is turned on at a positive ambient temperature of 10 minutes.
The form of the results of the control on the light panel of the block of stimulating signals is GODEN or FAILURE with indication of the measured values of the parameters.
The time of the Control and Testing Machine to enter the operation mode with the assessment of the state of readiness and serviceability of the Control and Testing Machine (without taking into account the deployment time of the Control and Testing Machine) is no more than 10 minutes.
Resource equipment operation to overhaul 2000 hours
The number of inspection cycles is at least 5000.
Curb weight Control and Testing Machine 9B990 not more than 11880 kg.
The distance of transportation of equipment of Control and Testing Machine on the base chassis is not more than 26000 km.
Control and Testing Machine 9В945
Control and Testing Machine 9V945 is intended to conduct TO-2 BM 9P157 and troubleshoot with an accuracy to a structurally replaceable unit (from the spare parts, tools and accessories kit -G) without disconnecting cable communication lines and removing equipment from the test object, as well as for integrated control of units from the group spare parts kit assembled in 1Q118 subsystems, and for measuring the parameters of the control equipment when adjusting and setting up the equipment after replacing the faulty unit.
The composition of Control and Testing Machine 9V945:
- - base chassis - car type KAMAZ 5350;
- - body-container K5350;
- - test equipment (CPS) 9B991 consisting of:
- - CPS 9V992 (used for testing 1K118);
- - CPS 9B993 (used when checking radar control system 1L32);
- - digital control unit;
- - block of stimulating signals;
- - measurement unit;
- - switching unit;
- - remote control panel;
- - set of cables;
- - standard measuring devices: frequency meter, oscilloscope, voltmeter, megohmmeter, multimeter;
- - Spare parts, tools and accessories kit is single;
- - a set of operational documentation.
In the body-container, a diesel-electric unit is installed to power the Shot Blasting Machine and the combat vehicle.
Shot Blasting Machine 9V945 is also powered from an industrial three-phase AC network of 380V ± 10% with a frequency of (50 ± 1) Hz.
Standard measuring devices are designed to test the subsystems KPA 9V991.
The testing of 9P157 combat vehicles using the KPA 9B991, located in the Shot Blasting Machine 9V945, is performed automatically by sequentially checking the parameters of individual subsystems of the test object. The transition from testing one subsystem to another is manually set by the MODE switch on the block of stimulating signals.
Checking the parameters of the combat vehicle with the help of the KPA 9В991 can be carried out both in automated and in manual mode.
Main technical characteristics of CPS 9V991
The method of monitoring the parameters of the combat vehicle and the spare parts, tools and accessories kit -G units of the equipment of these products is automated, parametric, tolerance.
Machine time checking one fighting machine without taking into account the time of connecting and disconnecting cables - 2 hours.
The deployment time of the Shot Blasting Machine from the traveling position to the working position is 2 hours.
Closing time Shot Blasting Machine from working position to marching - 15 min.
Duration of continuous work Shot Blasting Machine - 8 hours
Combat crew —1 driver and 1 operator.
The power consumed by the Shot Blasting Machine from a three-phase network of 380 V, 50 Hz - no more than 16 kW.
CPS is ready to work from the moment the power is turned on at a positive ambient temperature - 10 minutes.
The form of the results of the control on the light display of the block of stimulating signals - AVAILABLE or FAILURE with the ability to display the measured values of the parameters.
The time for the CPS to enter the operation mode with an assessment of the state of readiness and serviceability of the KPA (without taking into account the connection of cables to the distribution box) is no more than 10 minutes.
Resource equipment operation before overhaul - 2000 hours.
The checks cycles number - up to 1000.
Curb weight Shot Blasting Machine 9V945 - no more than 12,510 kg.